Rf-nano Nano V3.0 Micro Placa Usb Atmega328p Qfn32 5v 16m Ch340 Integrar Nrf24l01 Mais 2.4g sem Fio para Arduino
Original price was: R$ 28,50.R$ 27,29Current price is: R$ 27,29.
DÚVIDAS?
Envie um email para:
Componentes Ativos
Opção de Compra e tempo de entrega
Ficha técnica do produto
Características | Especificações |
---|---|
Pacote | Other |
Cutomizado | SIM |
Número do Modelo | Rf-nano |
Temperatura de Operação | . |
Potência de Dissipação | N/A |
Tensão de Alimentação | 5V |
Aplicação | Other |
Condição | Novo |
Tipo | Other |
Nome da Marca | Szytf |
Origem | CN (origem) |
Serial port: The built-in UART of ATmega328 can communicate with the outside through digital ports o (RX) and 1 (TX).
The NRF24LO1+ chip is integrated on the RF-NANO board, which makes it have unlimited transceiver functions, which is equivalent to combining an ordinary Nano board and an NRF24LO1 module into one, which is more convenient to use and small in size. The RF-NANO has exactly the same pins as the common Nano board, which is easy to transplant.
Processor introduction:
Processor: ATmega328
Working voltage: 5V Input voltage (recommended): 7-12V Input voltage (range): 6-20V
Digital IO pins: 14 (6 of which are used as PWM outputs) (D0~D13)
Analog input pins: 6 (A0~A5)
Io pin DC current: 40mA
Flash Memory: 32KB (2KB of which is used for bootloader)
SRAM: 2KB
EEPROM: 1KB (ATmega328)
USB to serial port chip: CH340
Working clock: 16 MHz
power supply:
RF-Nano power supply mode: Micro-USB interface power supply and external vin connected to 7~12v external DC power supply
Memory:
ATmega328 includes on-chip 32KB Flash, of which 2KB is used for Bootloader. Also 2KB SRAM and 1KB EEPROMo
input Output:
14 digital input and output ports: The working voltage is 5V, and the output and access limit current of each channel is 40mA. Each channel is configured with a 20-50K ohm internal pull-up resistor (not connected by default). In addition to this, some pins have specific functions.
Serial port signal Rx (No. o), TX (No. 1): provide the serial port receiving signal of TTL voltage level, and connect with the corresponding pin of FT232RI. External Interrupt (No. 2 and No. 3): Trigger the interrupt pin, which can be set as rising edge, falling edge or both.
Pulse width modulation PWM (3, 5, 6, 9, 10, 11): Provide 6 8-bit PWM outputs.
SPI ( 10(SS), 11(MOSI), 12(MISO), 13(SCK)): SPI communication interface.
LED (No. 13): Arduino is specially used to test the reserved interface of LED. When the output is high, the LED is turned on, otherwise, the LED is off when the output is low.
6 channels of analog input A0 to A5: each channel has a resolution of 10 bits (that is, the input has 1024 different values), the default input signal range is
0 to 5v, the upper limit of the input can be adjusted by AREF. In addition to this, some pins have specific functions.
TWI interface (SDAA4 and SCL A5): support communication interface (compatible with I2C bus).
AREF: The reference voltage of the analog input signal.
Reset: Reset the microcontroller chip when the signal is low.
Communication Interface:
Serial port: The built-in UART of ATmega328 can communicate with the outside through digital ports o (RX) and 1 (TX).
1. Rf-nano Nano V3.0 Micro Placa Usb Atmega328p
2. Componentes Ativos
3. Circuitos Integrados
4. Rf-nano Nano V3.0 Micro Placa Usb Atmega328p
Avaliações de Usuários
Seja o primeiro a avaliar “Rf-nano Nano V3.0 Micro Placa Usb Atmega328p Qfn32 5v 16m Ch340 Integrar Nrf24l01 Mais 2.4g sem Fio para Arduino”
Original price was: R$ 28,50.R$ 27,29Current price is: R$ 27,29.
Não existe nenhuma avaliação ainda.